87.060.30 (Solvents) 标准查询与下载

ASTM D3271-87(2012) 直接把可还原溶剂型涂料注射到气相色谱仪中进行溶剂分析的标准实施规程

1.1 This practice describes the techniques used to inject whole paint samples directly into a gas chromatograph to obtain a chromatogram from which the solvent composition may be established.2,3 1.2 This practice is not designed to be quantitative. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazard statement is given in 6.1.

Standard Practice for Direct Injection of Solvent-Reducible Paints Into a Gas Chromatograph for Solvent Analysis

ASTM D2634-86(1998) 乙酸甲基戊酯标准规格(95%级)

1.1 This specification covers methyl amyl acetate (95 % grade) for use in paint, varnish, and related products.1.2 For specific hazard information and guidance, see the supplier''s Material Safety Data Sheet for materials listed in this specification.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.

Standard Specification for Methyl Amyl Acetate (95% Grade)

ASTM D1310-86(1997)e1 用泰格开口杯装置测定液体闪点和燃点的测试方法

1.1 This test method covers the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between 0 and 325176;F (-18 and 165176;C) and fire points up to 325176;F.1.2 This test method, when applied to paints and resin solutions that tend to skin over or that are very viscous, gives less reproducible results than when applied to solvents. Note 18212;In order to conserve time and sample, the fire point of a material may be determined by the Tag Open-Cup Method by continuing the heating of the specimen to its fire point. Fire points may also be determined by Test Method D 92, which should be used for fire points beyond the scope of this test method.1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end use.1.4 This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

ASTM D3272-76(1998) 溶剂还原型油漆中分析用溶剂真空蒸馏的标准规程

1.1 This practice covers a vacuum distillation procedure that separates the solvents from the nonvolatile portion of paints so they may be analyzed. 1.2 An alternative procedure for the analysis of solvents in paints is described in Practice D3271. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Vacuum Distillation of Solvents From Solvent-Reducible Paints For Analysis